DokuWiki

0.1_resolution_get_error_message_from_makerware

Anonymous (anonymous@undisclosed.example.com) — 2024-10-31T15:25:52+00:00

Windows 10 with Makerware 3.7 is supported. Please make sure Makerware is cleanly installed, NO PATCH NEEDED. If you are not sure, please reinstall Makerware. If you encounter below problem, Ex: cannot slice at 0.1mm resolution, report to our support email:

abs_printed_object_warp_in_corner

Anonymous (anonymous@undisclosed.example.com) — 2024-10-31T15:25:53+00:00

ABS have more shrinkage than PLA. If you have thick corner on your model, the material have internal force to warp. There are some technic to solve this problem: 1) Changing to PLA is the easiest way to solve this problem. 2) Add a thin extension pad around the corner can increase stickiness to the platform.

access_denied_when_open_stl_file_in_replicatorg

Anonymous (anonymous@undisclosed.example.com) — 2024-10-31T15:25:54+00:00

If ReplicatorG is installed in “Program File” directory in newer Windows (later than win vista), may caused access denied warning. Solution: 1. Execute ReplicatorG using “Administrator privilege”. or 2. Copy ReplicatorG into other directory, Ex:

bearing_list_of_m180

Anonymous (anonymous@undisclosed.example.com) — 2024-10-31T15:25:55+00:00

Model Type Dim LM10SUU Bearing 10x19x29LM8SUU Bearing 8x15x17F623ZZ Flange bearings 3x10x4F605ZZ Flange bearings 5x14x5698Z Bearing 8x19x6F683ZZ Flange bearings 3x7x3MF105ZZ Flange bearings 5x10x4KFL08 Bearing pedestal Φ8

can_i_increase_heat_bed_output_watt

Anonymous (anonymous@undisclosed.example.com) — 2024-10-31T15:25:56+00:00

!!! Only for professionals, please do not proceed unless you know what you are doing. !!! RISK: Modify power voltage may cause power over load and damage power module !!! The designed output of heat bed is 24V 120W. Increase DC power input can raise output power of heat bed and extruder heater. There is a adjustable resistor on the power supply, can change output voltage.

changing_belt

Anonymous (anonymous@undisclosed.example.com) — 2024-10-31T15:25:56+00:00

A video to show how to replace the belts can download from this link: [ video]

changing_parameters

Anonymous (anonymous@undisclosed.example.com) — 2024-10-31T15:25:57+00:00

Please use USB connection to modify system parameters. To obtain config in memory, use command M503: M503 echo:Steps per unit: echo: M92 X93.00 Y93.00 Z1097.50 E97.00 echo:Maximum feedrates (mm/s): echo: M203 X150.00 Y150.00 Z1.50 E50.00 echo:Maximum Acceleration (mm/s2): echo: M201 X800 Y800 Z20 E10000 echo:Accelerations: P=printing, R=retract and T=travel echo: M204 P1500.00 R3000.00 T1500.00 echo:Advanced variables: S=Min feedrate (mm/s), T=Min travel feedrate (mm/s), B=minimum segme…

corner_ringing

Anonymous (anonymous@undisclosed.example.com) — 2024-10-31T15:25:58+00:00

Corner ringing Cause At higher print speeds, when the XY motion of the build platform or extruder makes a sudden change in direction, a ringing vibration may occur. Although it is quickly dampened, it nonetheless impacts surface finish. Corner ringing is particularly noticeable on long, flat surfaces and appears as ripples which rapidly diminish in amplitude. Like infill telegraphing, this can occur with non-accelerated printing as well as accelerated printing. The advantage of accelerated …

cura

Anonymous (anonymous@undisclosed.example.com) — 2024-10-31T15:25:58+00:00

Cura Cura is developed by Ultimaker to make 3D printing as easy and streamlined as possible. It includes a GUI to prepare a 3D file for printing and generate G-Code. X3G translation plug-ins is required to support Cura on Malyan Printer. Download

cura_2.3_usb_printing

Anonymous (anonymous@undisclosed.example.com) — 2024-10-31T15:26:01+00:00

Cura developer is not recommend printing though USB anymore. This part of function is now working as plugins module. Problem: USB printing not working on Cura 2.3 Cause: Original USB Printing plugins will communicate with stk500, which is a firmware update program for avr. However, this program does not close serial port correctly before plugins started baud rate detection. This problem will cause USB port cannot open and failed detecting USB printer.

cura_15

Anonymous (anonymous@undisclosed.example.com) — 2024-10-31T15:25:59+00:00

Platform may need to calibrate due to various first layer height in different start gcode Malyan mod of Cura can be download here. 1. MacOSX version: 2. Windows Version: 3. UPDATED Windows Version 15.06.03: 4. Profile for M180: Modifications:

cura_15_and_up

Anonymous (anonymous@undisclosed.example.com) — 2024-10-31T15:25:59+00:00

Platform may need to calibrate due to various first layer height in different start gcode Malyan mod of Cura can be download here. 1. MacOSX version: 2. Windows Version: Modifications: 1. Add M180 Machine support. 2. Allow save to X3G file.

cura_15_for_m150

Anonymous (anonymous@undisclosed.example.com) — 2024-10-31T15:26:00+00:00

Cura Profile for M150: High quality profile Balance profile Fast speed profile Step-by-step guide for modify slicing parameter:

cura_always_crash_after_loading_stl_file

Anonymous (anonymous@undisclosed.example.com) — 2024-10-31T15:26:02+00:00

This is a Cura bug, please refer to: Solution: Please update Cura to 15.06.03, link:

cura_is_not_able_to_save_as_x3g_format

Anonymous (anonymous@undisclosed.example.com) — 2024-10-31T15:26:03+00:00

If SD card is inserted, cura will use “save to card” dialog instead of “save to disk” by default. Solution: Load STL file and choose “save to disk” Select “X3G” extension

cura_is_not_able_to_set_platform_temperature_correctly

Anonymous (anonymous@undisclosed.example.com) — 2024-10-31T15:26:04+00:00

The post-processor in Cura have compatible problem with GCODE syntax: M190 S60 Solution: Update GPX.exe will solve problem, please download new GPX.exe from link. And overwrite “GPX.exe” in “C:\Program Files (x86)\Cura_15.06.02”.

cura_is_printing_using_left_extruder_or_not_extruding

Anonymous (anonymous@undisclosed.example.com) — 2024-10-31T15:26:04+00:00

Make sure CURA 15.06 is download from link: Follow below procedure to reset settings: Uninstall original CURA and install again. If problem remain, please report to our support email.

cura_setting_for_m200

Anonymous (anonymous@undisclosed.example.com) — 2024-10-31T15:26:05+00:00

Add new printer Select “Settings -> Printers -> Manage printer” menu. Click “Add” button, the “Add printer wizard” dialog will show. Choose “Custom FDM printer”. You can input a name for this printer then click “Add printer” to finish.

developer_guide_for_mm32_platform

Anonymous (anonymous@undisclosed.example.com) — 2024-10-31T15:26:07+00:00

!! This page is under construction !! If you have questions or report bug, please send email to: support at malyansys dot com. MM32 Platform Malyan M200/M100/M160/M190/M300/M450 printer use 32-bit MCU powered main board, which name we called MM32 platform. This document will describe detail about MM32 platform, to help 3rd party developer to create app to work with our device.

dual-extrusion_calibration_pattern_have_no_match_column_row

Anonymous (anonymous@undisclosed.example.com) — 2024-10-31T15:26:07+00:00

All M180 is pre-calibrated in factory, users don't have to calibrate dual-extrusion in most cases. If machine setting is erased(eeprom full reset), calibration value will be reset. The intergrated dual-extrusion calibration pattern can only adjust +-0.7mm at one time. If needed to adjust left for 2.0mm, please repeat to input value 1 for 3 times.

enable_pwm_feature_for_cooling

Anonymous (anonymous@undisclosed.example.com) — 2024-10-31T15:26:08+00:00

Update GPX included support for M106 and M107 command: M106 T0 S100 ; set pwm to 100, max value 255 M107 T0 ; disable pwm For ReplicatorG, please use M126 T0/M127 T0. PWM function is not supported in ReplicatorG interpreter.

error_message_from_makerware

Anonymous (anonymous@undisclosed.example.com) — 2024-10-31T15:26:08+00:00

extended_gcode_table

Anonymous (anonymous@undisclosed.example.com) — 2024-10-31T15:26:09+00:00

M550 INPUT_SSID = Get/Set SSID M551 INPUT_PASSWORD = Get/Set Password M552 = Display IP address M555 P1 = Reset wifi interface M556 = Display network status M560 = Update firmware using update.bin in microSD card M561 P1 = Change thermistor type

filament_funnel_extender_mod

Anonymous (anonymous@undisclosed.example.com) — 2024-10-31T15:26:10+00:00

Filament funnel extender: It extend the filament guide so the filament move up without any problem or twist. Works great! Thanks to Adrien Samon! Filament funnel extender

firmware_update_procedure

Anonymous (anonymous@undisclosed.example.com) — 2024-10-31T15:26:11+00:00

M150 Download: * Firmware for M150 (updated at 2016-4-18) Note: Two firmware available for M150, user can choose Repetier-firmware or Marlin Firmware updater usage: * Power off printer. * Press center button on panel. * Power up printer, please keep center button pressed.

getting_involved

Anonymous (anonymous@undisclosed.example.com) — 2024-10-31T15:26:12+00:00

Getting involved Please help us improve this wiki. You can write email to: wiki@malyansys.com.

gpx_for_translate_gcode_into_x3g_file

Anonymous (anonymous@undisclosed.example.com) — 2024-10-31T15:26:13+00:00

Malyan M180/W150 accept x3g file. Please translate gcode into x3g for SDcard printing. Download GPX for x3g translation, ,also reference to Cura for usage. (Cura 15.06 is supported)

home

Anonymous (anonymous@undisclosed.example.com) — 2024-10-31T15:26:15+00:00

Welcome to the wiki of the Malyan community, an open community dedicated to providing support for Malyan 3D Printer. If you want detailed guiding for operate your printer, please check Tutorial. If you are looking for support for your printer from Malyan, please take a look at our

how_to_change_pid_for_m180

Anonymous (anonymous@undisclosed.example.com) — 2024-10-31T15:26:16+00:00

Reference:

how_to_change_steps_per_mm_parameter

Anonymous (anonymous@undisclosed.example.com) — 2024-10-31T15:26:17+00:00

1. ReplicatorG: Please find ReplicatorG\machines\Malyan System.xml, replace corresponding stepspermm parameters. 2. Cura: Please find GPX.ini file in Cura directory.

how_to_clean_m150_extruder

Anonymous (anonymous@undisclosed.example.com) — 2024-10-31T15:26:17+00:00

Please reference to this video link:

how_to_clear_eeprom_to_factory_state

Anonymous (anonymous@undisclosed.example.com) — 2024-10-31T15:26:18+00:00

All machines are precalibrated in factory. For most of the time, users don't need to re-calibrate your printer. But if EEPROM information are modified, and user want to reset to factory state, please use “Restore settings” menu and choose “YES

install_filament

Anonymous (anonymous@undisclosed.example.com) — 2024-10-31T15:26:19+00:00

Loading Filament Before starting your first print, you must first load filament into each extruder you will be using. However, even if your printer has two extruders, it is strongly recommended that you start with a simple print which uses only a single extruder — preferably the right extruder. As such, you should not load filament into the second extruder until you actually need to use it. Malyan 3D printers come with filament, which is PLA plastic. While the loading directions are the same re…

invert_motor_direction

Anonymous (anonymous@undisclosed.example.com) — 2024-10-31T15:26:19+00:00

To invert motor direction, please use command M562. Remember to save eeprom and reset. M562 E ;Invert extruder motor M500 ;Save to eeprom ;Re-power the printer to make config valid

is_there_a_nozzle_cooler_on_m180

Anonymous (anonymous@undisclosed.example.com) — 2024-10-31T15:26:20+00:00

Latest M180 integrated nozzle cooler on extruder. If you purchased M180 without nozzle cooler, you can still DIY to add to your machine. Please check model and x3g for cooling support. There is a hanging wire (12V power for fan) hidden in front right corner of M180, you can connect to an external 12V fan.

lcd_no_display_on_m150

Anonymous (anonymous@undisclosed.example.com) — 2024-10-31T15:26:21+00:00

1. Open control box, double check connection on LCD module. 2. Make sure the resistor on back is adjusted to correct contrast. 3. Connect to USB and send some gcode to check firmware if system is up.

lcd_ui_corrupted

Anonymous (anonymous@undisclosed.example.com) — 2024-10-31T15:26:21+00:00

If UI on LCD panel become corrupted, please follow bellow procedure to recover: * Download * Setup wifi according to the manual. * Open web browser on computer, input “”. * Upload UI.bin and click “Upload UI”.

m200_display_please_wait

Anonymous (anonymous@undisclosed.example.com) — 2024-10-31T15:26:22+00:00

Problem: Screen display “Please wait” when selected print menu. 1. Select Preheat menu, check the temperature. If it is 0 ℃, you need to update firmware. 2.If the temperature is normal, and the XYZ axis can move, please kindly replace the SD card.

macosx

Anonymous (anonymous@undisclosed.example.com) — 2024-10-31T15:26:22+00:00

Driver USB driver for mainboard: Yosemite support Mac OSX 10.10 (Yosemite) need enable developer mode: sudo chown -R root:wheel usb.kext sudo chmod -R 755 usb.kext sudo nvram boot-args="kext-dev-mode=1" Test: sudo kextutil usb.kext Video link for step by step support to install CH340 driver

makerware

Anonymous (anonymous@undisclosed.example.com) — 2024-10-31T15:26:23+00:00

!! NOTE: If you are using latest firmware, Makerware 3.7 is NO LONGER need to patch. Please update firmware to latest and reinstall Makerware 3.7 !! Latest Makerware (3.8) Same as Makerware 3.7, if found problem please report to support email. Makerware 3.7

motherboard

Anonymous (anonymous@undisclosed.example.com) — 2024-10-31T15:26:25+00:00

Introduction MalyanBoard is a 3D Printer Control Board designed for Malyan 3D Printer. It adapts ATMEGA as the master control chip. MalyanBoard provides stable and excellent performance while reducing the difficulty of development and supports dual extruders. With the control software for dual-extrusion, it can realize double color printing to make printed items more attractive. Features:

my_sd_card_is_not_compatible_to_m180

Anonymous (anonymous@undisclosed.example.com) — 2024-10-31T15:26:26+00:00

Most SD card <2GB is tested without problem. We are not able to test every SD card in the market. If you find your SD card is not able to show file in M180, make sure SD card is properly formatted in FAT file system. FAT16 is prefered. !! NTFS is NOT supported !!.

nozzle_diameter

Anonymous (anonymous@undisclosed.example.com) — 2024-10-31T15:26:27+00:00

Below is dimension of nozzle. M180 Nozzle M150 Nozzle

open_bottom_cover

Anonymous (anonymous@undisclosed.example.com) — 2024-10-31T15:26:28+00:00

Repair electronic part require open the machine. Please follow bellow procedure to open: Step 1: Remove 6 screws to take the right and left plate out. Step 2: Remove the 4 screws of the lower right/right side plate Step 3: 1) Remove bellow 3 screw of the front plate.

recalibrate_x_y_axis_scale

Anonymous (anonymous@undisclosed.example.com) — 2024-10-31T15:26:29+00:00

Below contents are referenced from internet: Instructions See . The video shows two parts, an S-Shape hole and an S-Shape plug . The plug and the hole are edge to edge touching each other in the STL file. As show in the video, I can actually plug them together just by pushing real hard with bare hands, no tolerance compensations in the design, no drilling or filing, they just fit. The S-Shape is chosen de…

repetier-host

Anonymous (anonymous@undisclosed.example.com) — 2024-10-31T15:26:30+00:00

Repetier-host machine setting: Repetier-host slicing setting: Download from this link for import setting.

replicatorg_tool_change_command_bug_fix

Anonymous (anonymous@undisclosed.example.com) — 2024-10-31T15:26:30+00:00

ReplicatorG have bugs in translating G-Code command into X3G, may cause over speed in tool changing sequence. Solution 1: Update ReplicatorG Download ReplicatorG.jar and overwrite into /lib. Solution 2: Newest firmware have additional workaround to handle tool changing sequence for ReplicatorG Reference to

restrict

Anonymous (anonymous@undisclosed.example.com) — 2024-10-31T15:26:31+00:00

Restrict page Media manager

sample_code_for_web_interface

Anonymous (anonymous@undisclosed.example.com) — 2024-10-31T15:26:31+00:00

More API will be add soon. Send GCODE M565 to start print file cache.gc function start_p(){ $.ajax({ url: "set?code=M565", cache: false }).done(function(html) { }); } Send GCODE M566 to rename file cache.gc M566 newfilename.gc Get printing status

selected_left_extruder_but_temperature_not_raising_or_cold_extrusion

Anonymous (anonymous@undisclosed.example.com) — 2024-10-31T15:26:32+00:00

Follow below procedure to reset settings can solve problem:

shifted_layers

Anonymous (anonymous@undisclosed.example.com) — 2024-10-31T15:26:33+00:00

There are several possibility to cause X-axis shift: 1. Glass not fix, loose while printing. 2. Eng-stopper triggered by noise. Always shift to left side. 3. Cool nozzle hit wrapped corner. Heat up both extruder can help. 4. Too fast printing speed. Please slow down to 50% to test.

simplify3d

Anonymous (anonymous@undisclosed.example.com) — 2024-10-31T15:26:34+00:00

There is already a profile for the Malyan M180 available in Simplify3D. Just go to Help > Configuration Assistant, and select that printer from the list

slic3r

Anonymous (anonymous@undisclosed.example.com) — 2024-10-31T15:26:36+00:00

Dual extrusion profile for Slic3r 1.2.8 This tutorial will guide you setup proper profile for Slic3r to use with Malyan M180 3D Printer. Windows version of Slic3r can be download here. MacOSX user please follow below procedure to modify profile. First run

some_mechanic_parameters

Anonymous (anonymous@undisclosed.example.com) — 2024-10-31T15:26:37+00:00

X and Y axis pulley Diameter = 10.3 mm Teeth = 17 MXL = 2.032mm Pitch High Temperature Insulation Wool Blanket

start.gcode

Anonymous (anonymous@undisclosed.example.com) — 2024-10-31T15:26:37+00:00

(**** beginning of start.gcode ****) (This is start code for The Replicator running a single material print) M73 P0 (enable build progress) M103 (disable RPM) G21 (set units to mm) G90 (set positioning to absolute) (**** begin homing ****) G162 X Y F4000 (home XY axes maximum) G161 Z F400 (home Z axis minimum) G92 Z-5 (set Z to -5) G1 Z0.0 (move Z to "0") G161 Z F100 (home Z axis minimum) M132 X Y Z A B (Recall stored home offsets for XYZAB axis) (**** end homing ****) G92 X146.5 Y73 Z5 G1 X105 …

start

Anonymous (anonymous@undisclosed.example.com) — 2024-11-11T08:33:55+00:00

stepper_motor_parameters

Anonymous (anonymous@undisclosed.example.com) — 2024-10-31T15:26:39+00:00

M180 use 5 stepper motors. The electric parameter is shown below: Model Step Angle Phase Current Phase Resistance Phase Inductance Holding Torque Detent Torque Rotor Inertia NEMA17-34mm 1.8° 0.4A 24 Ohm 15 mH

temperature_display_353c

Anonymous (anonymous@undisclosed.example.com) — 2024-10-31T15:26:39+00:00

Short circuit of thermistor will cause ADC reading 0, this value is corresponding to 353C according to internal temperature table. If reading is 353C, please double check if there is any short circuit between sensor and GND.

test_print

Anonymous (anonymous@undisclosed.example.com) — 2025-02-14T17:06:44+00:00

Bro they didn't create this page already you can dm me in gmail: kayaerimX@gmail.com

the_operation_method_of_dual_nozzle_calibration

Anonymous (anonymous@undisclosed.example.com) — 2024-10-31T15:26:40+00:00

Replicator 1 Dual Nozzle Calibration Print calibration script (File->Scripts->Calibration->Replicator 1&2->Dual Nozzle Calibration.gcode). When it does start, you’ll see it print a series of straight lines parallel to the front of the build platform, starting at the front left corner of the platform and extending back. The second series of lines will be perpendicular to these, and will start at the center of the platform and extend left.Then the second nozzle will print a set of lines along…

tune_pid

Anonymous (anonymous@undisclosed.example.com) — 2024-10-31T15:26:42+00:00

Note: Firmware 1.7 and below may cause reset upon M303 command. Update firmware will solve this bug. M303 S190 Autotune PID value for extruder at 190C. M301 Manually set PID parameters P I and D. M500 Save parameters to eeprom.

tutorial

Anonymous (anonymous@undisclosed.example.com) — 2024-10-31T15:26:43+00:00

A step by step guide Step 1 – Generate or find a Model Download a model from internet There are several website providing free 3D object for download. * www.thingiverse.com Generating a Model using CAD In order to open the file in Slicer, it must be saved as a STL (*.stl) file. In the “Save as” drop down menu, select STL as the file type.

type_of_thermistors_of_m200

Anonymous (anonymous@undisclosed.example.com) — 2024-10-31T15:26:43+00:00

Extruder and hotbed are all 100K NTC resistor with beta 3950.

unlock_some_limit_parameters_of_printer

Anonymous (anonymous@undisclosed.example.com) — 2024-10-31T15:26:44+00:00

!! CAUTION: HEATING EXTRUDER ABOVE 250 DEGREE FOR LONG TIME MAY AFFECT LIFE SPAN OF FILAMENT PASS !! If your filament pass is broken, please replace a new one. 1. Our default GPX interpreter have a limit of a) Platform temperature lock below 90 degree. b) Nozzle temperature lock below 250 degree.

utility_to_test_com_port

Anonymous (anonymous@undisclosed.example.com) — 2024-10-31T15:26:45+00:00

A modified Putty can use for testing com port. Link:

video_for_replacement_of_component

Anonymous (anonymous@undisclosed.example.com) — 2024-10-31T15:26:46+00:00

1. Changing rotary PCB

why_z-axis_have_offset_when_start_print

Anonymous (anonymous@undisclosed.example.com) — 2024-10-31T15:26:47+00:00

The problem is caused by wrong feedrate of Z-axis or wrong resolution Z-axis screw (1600 steps/mm). To solve this problem, please reset eeprom and try updated Makerware in our website: Or modify Z-axis feedrate for slicer manually. Makerware users: Please check

x_y_axis_not_moving

Anonymous (anonymous@undisclosed.example.com) — 2024-10-31T15:26:49+00:00

Problem: X-axis motor not moving but Y-axis good. Or, Y-axis not moving and X-axis OK. Solution: Please follow below procedure to check: * Power off printer, remove power plug * Open bottom cover * Swap X and Y axis motor connector * Power on, enter Monitor menu