firmware_update_procedure
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
firmware_update_procedure [2016/06/13 12:14] admin [M200] |
firmware_update_procedure [2019/05/16 10:42] (current) |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| + | ===== M150 ===== | ||
| + | |||
| + | Download: | ||
| + | * [[http://malyansys.com/download/firmware-m150.rar| Firmware for M150]] (updated at 2016-4-18) | ||
| + | |||
| + | Note: Two firmware available for M150, user can choose Repetier-firmware or Marlin | ||
| + | |||
| + | Firmware updater usage: | ||
| + | - Power off printer. | ||
| + | - Press center button on panel. | ||
| + | - Power up printer, please keep center button pressed. | ||
| + | - Release center button. | ||
| + | - Look up COM port from windows device manager. Type below command into windows console: avrdude.exe -v -p atmega1284p -c arduino -P com4 -b 57600 -V -U flash:w:marlin.hex | ||
| + | - Reboot printer if necessary. | ||
| + | |||
| + | Source Code: | ||
| + | |||
| + | * All open source code is in Malyan System official github: [[https://github.com/MalyanSystem/Malyan-M150-Marlin]] | ||
| + | |||
| + | |||
| + | ===== M180 ===== | ||
| + | |||
| + | ==== Motion Controller ==== | ||
| + | Firmware updater usage: | ||
| + | - Power off printer. | ||
| + | - Press center button on panel. | ||
| + | - Power up printer, please keep center button pressed. | ||
| + | - Release center button. | ||
| + | - Look up COM port from windows device manager. Type below command into windows console(Require administrator privilage): update.exe -P COM4 | ||
| + | - Reboot printer if necessary. | ||
| + | |||
| + | Download： | ||
| + | * [[http://malyansys.com/download/up.exe| Latest Firmware for M180]] (updated at 2015-7-26), enhance support for Makerware 3.7 | ||
| + | * [[http://malyansys.com/download/update-M180.exe| Firmware for M180]] | ||
| + | * [[http://malyansys.com/download/update-M180-OEM.exe| OEM version firmware for M180]] | ||
| + | * [[http://malyansys.com/download/update-W150.exe| Firmware for W150]] | ||
| + | |||
| + | ==== GUI ==== | ||
| + | GUI update procedure: | ||
| + | - Power off printer. | ||
| + | - Press center button on panel. | ||
| + | - Power up printer, please keep center button pressed. | ||
| + | - Release center button. | ||
| + | - Push center button again to switch to LCD update mode. | ||
| + | - Execute GUI_UPDATE.EXE, select UPDATE_S.bin and correct COM port. | ||
| + | - Start update | ||
| + | |||
| + | GUI firmware download link： | ||
| + | |||
| + | * [[http://www.malyansys.com/download/GUI_UPDATE.EXE| GUI_UPDATE]] | ||
| + | * [[http://www.malyansys.com/download/UPDATE_S.bin| LCD Firmware for M180]] | ||
| + | |||
| + | ==== Experimental firmware ==== | ||
| + | |||
| + | !!Please note, experimental firmware is only for testing purpose!! | ||
| + | |||
| + | Some users have difficulty with avrdude, please choose m2560 part and stk500v1 programmer in command line. | ||
| + | |||
| + | Reduced cooling fan speed for ABS: | ||
| + | * [[http://malyansys.com/download/exp20151102.exe| Experimental Firmware for M180]] (updated at 2015-11-2) | ||
| + | |||
| + | Marlin firmware, accept plain text GCode: | ||
| + | * [[http://malyansys.com/download/exp20151214.exe| Experimental Marlin Firmware]] (updated at 2015-12-14) First port of Marlin | ||
| + | * [[http://malyansys.com/download/exp20160103.exe| Experimental Marlin Firmware]] (updated at 2016-01-03) Changed default parameters, enabled EEPROM support. | ||
| + | |||
firmware_update_procedure.txt · Last modified: 2019/05/16 10:42 (external edit)
Page Tools
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 4.0 International
