This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision | ||
firmware_update_procedure [2016/06/13 00:21] admin [M200] |
firmware_update_procedure [2019/05/16 10:42] (current) |
||
---|---|---|---|
Line 1: | Line 1: | ||
+ | ===== M150 ===== | ||
+ | |||
+ | Download: | ||
+ | * [[http://malyansys.com/download/firmware-m150.rar| Firmware for M150]] (updated at 2016-4-18) | ||
+ | |||
+ | Note: Two firmware available for M150, user can choose Repetier-firmware or Marlin | ||
+ | |||
+ | Firmware updater usage: | ||
+ | - Power off printer. | ||
+ | - Press center button on panel. | ||
+ | - Power up printer, please keep center button pressed. | ||
+ | - Release center button. | ||
+ | - Look up COM port from windows device manager. Type below command into windows console: avrdude.exe -v -p atmega1284p -c arduino -P com4 -b 57600 -V -U flash:w:marlin.hex | ||
+ | - Reboot printer if necessary. | ||
+ | |||
+ | Source Code: | ||
+ | |||
+ | * All open source code is in Malyan System official github: [[https://github.com/MalyanSystem/Malyan-M150-Marlin]] | ||
+ | |||
+ | |||
+ | ===== M180 ===== | ||
+ | |||
+ | ==== Motion Controller ==== | ||
+ | Firmware updater usage: | ||
+ | - Power off printer. | ||
+ | - Press center button on panel. | ||
+ | - Power up printer, please keep center button pressed. | ||
+ | - Release center button. | ||
+ | - Look up COM port from windows device manager. Type below command into windows console(Require administrator privilage): update.exe -P COM4 | ||
+ | - Reboot printer if necessary. | ||
+ | |||
+ | Download: | ||
+ | * [[http://malyansys.com/download/up.exe| Latest Firmware for M180]] (updated at 2015-7-26), enhance support for Makerware 3.7 | ||
+ | * [[http://malyansys.com/download/update-M180.exe| Firmware for M180]] | ||
+ | * [[http://malyansys.com/download/update-M180-OEM.exe| OEM version firmware for M180]] | ||
+ | * [[http://malyansys.com/download/update-W150.exe| Firmware for W150]] | ||
+ | |||
+ | ==== GUI ==== | ||
+ | GUI update procedure: | ||
+ | - Power off printer. | ||
+ | - Press center button on panel. | ||
+ | - Power up printer, please keep center button pressed. | ||
+ | - Release center button. | ||
+ | - Push center button again to switch to LCD update mode. | ||
+ | - Execute GUI_UPDATE.EXE, select UPDATE_S.bin and correct COM port. | ||
+ | - Start update | ||
+ | |||
+ | GUI firmware download link: | ||
+ | |||
+ | * [[http://www.malyansys.com/download/GUI_UPDATE.EXE| GUI_UPDATE]] | ||
+ | * [[http://www.malyansys.com/download/UPDATE_S.bin| LCD Firmware for M180]] | ||
+ | |||
+ | ==== Experimental firmware ==== | ||
+ | |||
+ | !!Please note, experimental firmware is only for testing purpose!! | ||
+ | |||
+ | Some users have difficulty with avrdude, please choose m2560 part and stk500v1 programmer in command line. | ||
+ | |||
+ | Reduced cooling fan speed for ABS: | ||
+ | * [[http://malyansys.com/download/exp20151102.exe| Experimental Firmware for M180]] (updated at 2015-11-2) | ||
+ | |||
+ | Marlin firmware, accept plain text GCode: | ||
+ | * [[http://malyansys.com/download/exp20151214.exe| Experimental Marlin Firmware]] (updated at 2015-12-14) First port of Marlin | ||
+ | * [[http://malyansys.com/download/exp20160103.exe| Experimental Marlin Firmware]] (updated at 2016-01-03) Changed default parameters, enabled EEPROM support. | ||
+ | |||